ARM9 based project PCB layout
Required skills: CAD/CAM, Electrical Engineering, Electronics, PCB Layout, Product Design
We have an ARM9 based design and need the PCB layout done.
Project major components:
- LPC3250 CPU, BGA296 package 0.8mm pitch, 266MHz operating speed
- NAND flash, BGA63 package 0.8mm pitch, 8-bit interface
- DDR SDRAM, BGA60 package, 0.8mm pitch, 16-bit interface
- USB 2.0 full speed host (12Mbps)
- Buffered general purpose parallel inputs and outputs
- NV serial SRAM
Schematic design already exists, and can be modified where needed as the board layout progresses. We expect the PCB to be 6-8 layer, aiming for size approx. 8cm x 6cm or smaller. Use of small packages like 0402 and BGA is expected. Final design must meet CE regulatory requirements, so designing for EMC is a definite requirement which will include the design for the shielding “can/s” .
Layout must be done using Altium Designer. Daily updates and file submissions will be expected to track progress and assist where necessary.
We will arrange prototype manufacture, EMC testing, mass production. Some additional follow-up work may be required depending on EMC testing outcome.
Deliverables required:
- Altium .pcbdoc file
- Reports containing circuit simulation results, PCB track lengths, and track impedance matching calculations for high frequency traces.
Project major components:
- LPC3250 CPU, BGA296 package 0.8mm pitch, 266MHz operating speed
- NAND flash, BGA63 package 0.8mm pitch, 8-bit interface
- DDR SDRAM, BGA60 package, 0.8mm pitch, 16-bit interface
- USB 2.0 full speed host (12Mbps)
- Buffered general purpose parallel inputs and outputs
- NV serial SRAM
Schematic design already exists, and can be modified where needed as the board layout progresses. We expect the PCB to be 6-8 layer, aiming for size approx. 8cm x 6cm or smaller. Use of small packages like 0402 and BGA is expected. Final design must meet CE regulatory requirements, so designing for EMC is a definite requirement which will include the design for the shielding “can/s” .
Layout must be done using Altium Designer. Daily updates and file submissions will be expected to track progress and assist where necessary.
We will arrange prototype manufacture, EMC testing, mass production. Some additional follow-up work may be required depending on EMC testing outcome.
Deliverables required:
- Altium .pcbdoc file
- Reports containing circuit simulation results, PCB track lengths, and track impedance matching calculations for high frequency traces.
Posted In:CAD/CAMElectrical EngineeringElectronicsPCB Layout |
Related projects:
ARM9 based system PCB design
FBGA
-- 48 TSOP NAND Flash
-- TSOP Ethernet PHY
-- GPIOs and serial interfaces
Layout must be done using ORCAD software (Layout or PCB designer).
Deliverables will be ORACAD PCB files as well as Gerber production files.
PCB track length and impedance calculation are also needed.
Daily reports are mandatory.
Once deliverables ready a follow-up project for prototype manufacturing will be requiered.
-- 48 TSOP NAND Flash
-- TSOP Ethernet PHY
-- GPIOs and serial interfaces
Layout must be done using ORCAD software (Layout or PCB designer).
Deliverables will be ORACAD PCB files as well as Gerber production files.
PCB track length and impedance calculation are also needed.
Daily reports are mandatory.
Once deliverables ready a follow-up project for prototype manufacturing will be requiered.
PCB Layout for LED Project
make a new PCB layout that allows for 5 RGB LEDs at full brightness connected to the same controller. The power source will be 2 x CR2032. The 5 RGB LEDs won't be soldered to the PCBA. I need a recommendation on a connector to connect the wires from the 5 RGB LEDs to the PCB (supply this in your bid if you have any in mind).
Please provide examples of previous PCB layout work with your bid.
Please provide examples of previous PCB layout work with your bid.
Simple Circuit and PCB Layout
I ALREADY HAVE THE PROGRAMMING OF THE MICROCONTROLLER DONE, so this is not included in the project.
I just need the schematic and the PCB layout for this project.
I have many of the components needed so I would like to use them in this project if possible.
The files attached will give you an idea of how I failed and the components I used. Please tell me if this is even conveniently possible.
Thank You.
PCB Layout
I have a PCB layout based on an atmel 32 bit microcontrolller, with an erthernet PHY.
It has
1 RJ45 Connector
3 off 2.5mm audio jacks
1 off 10 way terminal block
1 barrel power jack
The PCB size is 90mm x 78mm
It has
1 RJ45 Connector
3 off 2.5mm audio jacks
1 off 10 way terminal block
1 barrel power jack
The PCB size is 90mm x 78mm
PCB Layout and Design of XBee Bridge
l required component layout expectation and a complete schematic file, along with libraries of most of the relavent components. I need the PCB Layout completed in only two layers with all SMD components. This project MUST be completed in CadSoft Eagle and will require the delivery of a DRC checked and passing .brd file derived from the provided .sch file
PCB layout help needed - Diptrace only
M.
6. Again please use Diptrace only.
Additional files submitted: (Files are only available for logged in users)
1.dip
6. Again please use Diptrace only.
Additional files submitted: (Files are only available for logged in users)
1.dip
PCB Layout Project
Hi,
I am looking for PCB layout engineer who can design boards in MentorPADS.
I have a PDF schmeatics and I need to design a Board in PADS.
Thanks,
GS
I am looking for PCB layout engineer who can design boards in MentorPADS.
I have a PDF schmeatics and I need to design a Board in PADS.
Thanks,
GS
STM32 Ethernet Switch Module Electronic Design & PCB layout
nd connectors. We require Schematic Capture and circuit design from block diagram level and double sided 6 to 8 layer PCB layout approx size 70mm by 55mm.
Optional Embedded code development for Interniche IP Stack, web server, ethernet switch management on telnet / CLI / web / SNMP etc. Web based programmable datalogger application, approx code budget 256K inc Stack.
We are UK based.
Optional Embedded code development for Interniche IP Stack, web server, ethernet switch management on telnet / CLI / web / SNMP etc. Web based programmable datalogger application, approx code budget 256K inc Stack.
We are UK based.
pcb layout of a simetric dc source +12 +5 -5 -12
this is a complete circuit of a simetric dc source with 4 options of voltages (12 +5 -5 -12).
of course with the respective pcb layout.
the maximun current that the circuit can provide is 0.5 A without disipation element(and 1 A with a decent disipation element)
the project was made with IC 7805,7812,7905,7912.
just available for venezuela
of course with the respective pcb layout.
the maximun current that the circuit can provide is 0.5 A without disipation element(and 1 A with a decent disipation element)
the project was made with IC 7805,7812,7905,7912.
just available for venezuela
A Small 4 Layers and one 2 layers PCB Layout modify
nector components. And one new connector need to create. This boards only little modify.
The 110mm X 111mm 4 Layers is about 30 change items.
Including modify drill hole size, change component size (C0603=>C0402), change component side, re-layout the DIP jumper etc. One new TQPF128 need to create, One IDE20 need convert to SMD type.
We will provide you the netlist file.
You need use allegro (above 16.0) as layout tool.
The 110mm X 111mm 4 Layers is about 30 change items.
Including modify drill hole size, change component size (C0603=>C0402), change component side, re-layout the DIP jumper etc. One new TQPF128 need to create, One IDE20 need convert to SMD type.
We will provide you the netlist file.
You need use allegro (above 16.0) as layout tool.
A small 4 Layer PCB Layout modify
only 26 components .
The 102mmx25mm 2 layers change to different connector and only 4 connector components.
These above two boards only little modify.
The 110mm X 111mm 4 Layers is about 30 change items.
Including modify drill hole size, change component size (C0603=>C0402), change component side, re-layout the DIP jumper etc.
We will provide you the netlist file.
You must use allegro (above 16.0) as layout tool.
The 102mmx25mm 2 layers change to different connector and only 4 connector components.
These above two boards only little modify.
The 110mm X 111mm 4 Layers is about 30 change items.
Including modify drill hole size, change component size (C0603=>C0402), change component side, re-layout the DIP jumper etc.
We will provide you the netlist file.
You must use allegro (above 16.0) as layout tool.
PCB Layout Outsourcing
International company located in HK Science Park looking for Engineering Support.
Job Definition:
Electricial schematic capture, component modeling and PCB layout.
please contact Peter Li for detail.
Minimum time two months.
immediate availiable.
Job Definition:
Electricial schematic capture, component modeling and PCB layout.
please contact Peter Li for detail.
Minimum time two months.
immediate availiable.
PCB layout rev2
Need to get small PCB layout from pdf schematic.
I already have garber files using altium if needed from previous revision and everything is working fine with rev 1 board.
On this rev 2 only new module and some minor changes are added for which i need new pcb design.
I already have garber files using altium if needed from previous revision and everything is working fine with rev 1 board.
On this rev 2 only new module and some minor changes are added for which i need new pcb design.
PCB Layout design and/or prototypes manufacturing in 2012
t, but faster service is preferable.
Do not hesitate to ask any questions and suggest any interesting (“revolutionary”) ideas.
We are capable to Google and search for similar services (in other words, we are well aware of existing services), but prefer to have a more private, easy and cheaper solution. So please take it into account and bid low!!!
(the more specific details will be shared before finalising the bid)
Do not hesitate to ask any questions and suggest any interesting (“revolutionary”) ideas.
We are capable to Google and search for similar services (in other words, we are well aware of existing services), but prefer to have a more private, easy and cheaper solution. So please take it into account and bid low!!!
(the more specific details will be shared before finalising the bid)
PCB layout for a small circuit
Your mission is to design the PCB layout for a circuit of a simple bluetooth circuit, using the Eagle software.
Thank you.
PCB layout
0pxborder-style: none; border-spacing: 0px;">
PCB Layout designer (long term)
Experienced with 50Amp+ tracks and 10-20 layers
Able to solve complex PCB problems.
Very good wriiten and spoken English
Must have a legal Altium summer 09 or later version license
Proof of legal license will required via the Altium office
Experienced with 50Amp+ tracks and 10-20 layers
Able to solve complex PCB problems.
Very good wriiten and spoken English
Must have a legal Altium summer 09 or later version license
Proof of legal license will required via the Altium office
Design Satellite Tuner Voltage Booster & PCB Layout
ld be small footprint and will be placed in circuit between the tuner antenna input socket and the antenna itself. It should introduce minimal noise into the system and the connectors will be female F-connector sockets.
If you wish also to bid for construction of the PCB's only (2 required at this time - unpopulated), please do so.
Thank you.
If you wish also to bid for construction of the PCB's only (2 required at this time - unpopulated), please do so.
Thank you.
Altium PCB layout and coaching
Looking for someone to spend two weeks training engineers with Altium designer, adding some parts to our library and performing PCB layout.
ANALOG BOARD PCB layout under Altium Designer
Additional information submitted: 03/15/2011 at 11:16 EDT:
errata: is "8 asymetrical/differential inputs", should be "8 symetrical/differential inputs"
RELAY BOARD PCB layout under Altium Designer
br>- PCB layout under Altium Designer
- 3D view of PCB under Altium Designer
- BOM
- specification of customized components (if any)
4. deadline: 3 days
5. payments:
- first milestone - 30% total payment - after receiving schematics
- final payment - 70% total payment - after receiving PCB layout and 3D View (completed docs)
- 3D view of PCB under Altium Designer
- BOM
- specification of customized components (if any)
4. deadline: 3 days
5. payments:
- first milestone - 30% total payment - after receiving schematics
- final payment - 70% total payment - after receiving PCB layout and 3D View (completed docs)
