PCB step and repeat
Required skills: PCB Layout
I would like to get 2 PCB's (gerber data provided) repeated for a panel layout.
The layout for both PCB's will be 5 across x 10 down. The panel needs a gap in the y direction of 18mm and 0mm in the x direction. There needs to be a border of 10mm all around the outside. One PCB is 48mm(x) x 16mm(y) approx and the other is 45.5mm (x) x 17mm (y) approx.
They are both single sided, with solder mask and silkscreen and one of them has a peelable mask.
The layout for both PCB's will be 5 across x 10 down. The panel needs a gap in the y direction of 18mm and 0mm in the x direction. There needs to be a border of 10mm all around the outside. One PCB is 48mm(x) x 16mm(y) approx and the other is 45.5mm (x) x 17mm (y) approx.
They are both single sided, with solder mask and silkscreen and one of them has a peelable mask.
Posted In:PCB Layout |
Related projects:
PCB editing and circuit design
double layer, SMD mixed with TH, so you need to know how to make the board more manufacturable
You will need to edit the PCB layout, send it to production (5 samples) and assembly it.
I also looking for solidworks designer.
If you think you can handle those kind of jobs,
Please feel free to visit my pa ge:
webspawner.com/users/pmposible/index.html
Thanks,
PM, posible
You will need to edit the PCB layout, send it to production (5 samples) and assembly it.
I also looking for solidworks designer.
If you think you can handle those kind of jobs,
Please feel free to visit my pa ge:
webspawner.com/users/pmposible/index.html
Thanks,
PM, posible
PIC microcontroller/ PCB design and prototype
ional information submitted:
08/11/2010 at 20:54 EDT:
The above link is a evaluation board we have used with success and we woud like to move on to the next stage.
We need a industry standard pcb file for our record and would like a minimum of 5 pcb prototypes with all components installed.
Thanks and good luck
Malik Fareed
The above link is a evaluation board we have used with success and we woud like to move on to the next stage.
We need a industry standard pcb file for our record and would like a minimum of 5 pcb prototypes with all components installed.
Thanks and good luck
Malik Fareed
PCB layout and prototyping.
components.
The schematics contains one Intel Processor(496 BGA),two SRAMs, one PLD and 96 differential connections coming in from a 100 pin connector.
I will provide the schematics to the selected providers, as I can't put it here in open share.
I please keep the cost as low as possible, because once the board is through I may need another 50 of them.
Thanks,
Brad.
The schematics contains one Intel Processor(496 BGA),two SRAMs, one PLD and 96 differential connections coming in from a 100 pin connector.
I will provide the schematics to the selected providers, as I can't put it here in open share.
I please keep the cost as low as possible, because once the board is through I may need another 50 of them.
Thanks,
Brad.
PCB engineering and design
stom project im working on. I do not have any schematics but i am also not on a time constraint. Attached is a word document with all the info for the requirements. It has websites for all the devices being controlled and i can also mail you these devices to work with. The size and layers of the board are not important because i will have plenty of room and can manipulate it into my design easily. Please feel free to ask any questions.
CC2533 PCB Design and assembly
an take care also to find the all components
Antenna design as follow: http://www.ti.com/lit/an/swru120b/swru120b.pdf
or dedicated component on PCB
Components type are SMD 0402 package.
6 PCB in total, where 4 of them will be FULLY ASSEMBLED AND WORKING.
Please quote me your design costs + the components costs
I need this done within 1 month.
A simple C program connect to another one just to show that it works ok.
Antenna design as follow: http://www.ti.com/lit/an/swru120b/swru120b.pdf
or dedicated component on PCB
Components type are SMD 0402 package.
6 PCB in total, where 4 of them will be FULLY ASSEMBLED AND WORKING.
Please quote me your design costs + the components costs
I need this done within 1 month.
A simple C program connect to another one just to show that it works ok.
PCB Layout and Design of XBee Bridge
l required component layout expectation and a complete schematic file, along with libraries of most of the relavent components. I need the PCB Layout completed in only two layers with all SMD components. This project MUST be completed in CadSoft Eagle and will require the delivery of a DRC checked and passing .brd file derived from the provided .sch file
Altium PCB layout and coaching
Looking for someone to spend two weeks training engineers with Altium designer, adding some parts to our library and performing PCB layout.
Step-up (boost) DC-DC Converter, 5KVA
-start.
The output voltage can be controlled using analog signal (output from DAC) or digitally.
The milestones will be
1. Simulation
2. Bill of Materials (BOM)
3. PCB Layout using Altium
4. PCB fab and assembly
5. Laboratory Test.
Please inform me your previous works relating to this project.
Regards,
zamrud20
The output voltage can be controlled using analog signal (output from DAC) or digitally.
The milestones will be
1. Simulation
2. Bill of Materials (BOM)
3. PCB Layout using Altium
4. PCB fab and assembly
5. Laboratory Test.
Please inform me your previous works relating to this project.
Regards,
zamrud20
USB hub + bridge PCB design and layout
ne sata connector,
one power connector(12v). Board is self-powered, and on-board regulators must be added to convert incoming 12v to required voltages, including an extra 5v out for powering an optical drive.
Mechanical drawing for layout (outline, mounting holes, and connector placement) will be provided upon award of contract. Approximate board size is 3" x 3" and can be 4-layer.
one power connector(12v). Board is self-powered, and on-board regulators must be added to convert incoming 12v to required voltages, including an extra 5v out for powering an optical drive.
Mechanical drawing for layout (outline, mounting holes, and connector placement) will be provided upon award of contract. Approximate board size is 3" x 3" and can be 4-layer.
Simple PCB Layout and Code
Additional information submitted: 06/25/2010 at 3:18 EDT:
6. This pcb is to be powered by a 12v - 24 v external power source. Use Voltage regulator that can bring it down to pic requirement voltage 4v min to 5.5v max
pcb layout and routing for rf design project
ns_10-05-24-1.pdf'>RFCOMMUNICATOR_InitialPlacementTop_WithDimensions_10-05-24-1.pdf
RFCOMMUNICATOR_InterimSchematics_NoModem_B4Annotate_10-05-24-1.pdf
BOM.xls
RFCOMMUNICATOR_InterimSchematics_NoModem_B4Annotate_10-05-24-1.pdf
BOM.xls
Microchip PIC16 Microcontroller PCB & Driver design
wledge to complete the job. We can share this information with you to redesign and use as a point of reference. We believe the design is flawed in the sensor voltage feedback signal being too low for the PIC18 micro controller.
Please only bid if you think this is an easy project and have experience in designing PCB's and writing code for the driver. Feel free to ask any questions you wish. Thank you for reviewing my project!
Please only bid if you think this is an easy project and have experience in designing PCB's and writing code for the driver. Feel free to ask any questions you wish. Thank you for reviewing my project!
Design and Develop a Telemetry Unit
DMA remote data download capability. The requirement is to
1. Come up with design
2. Have a review with concerned engineers
3. PCB Layout and manufacture of single unit.
4. This unit will go through a testing process. Any changes or fixes should be supported during the phase.
5. Develop software related to the hardware and remote data download.
We can discuss more once we finalize on the freelancer.
Thanks
1. Come up with design
2. Have a review with concerned engineers
3. PCB Layout and manufacture of single unit.
4. This unit will go through a testing process. Any changes or fixes should be supported during the phase.
5. Develop software related to the hardware and remote data download.
We can discuss more once we finalize on the freelancer.
Thanks
ARM9 based system PCB design
FBGA
-- 48 TSOP NAND Flash
-- TSOP Ethernet PHY
-- GPIOs and serial interfaces
Layout must be done using ORCAD software (Layout or PCB designer).
Deliverables will be ORACAD PCB files as well as Gerber production files.
PCB track length and impedance calculation are also needed.
Daily reports are mandatory.
Once deliverables ready a follow-up project for prototype manufacturing will be requiered.
-- 48 TSOP NAND Flash
-- TSOP Ethernet PHY
-- GPIOs and serial interfaces
Layout must be done using ORCAD software (Layout or PCB designer).
Deliverables will be ORACAD PCB files as well as Gerber production files.
PCB track length and impedance calculation are also needed.
Daily reports are mandatory.
Once deliverables ready a follow-up project for prototype manufacturing will be requiered.
Help in search and entering data
ite.
OPTIONAL: In addition to the 1000 records needed to be added to the database, if you are able to find a big list of doctors in the "GTA" with names and phone numbers, but lacking other information, please provide us a SEPARATE quote to offer us this list of doctor records for later use.
NOTE: this can lead to other follow-up opportunities later, please provide quality work.
Ask if have any questions.
OPTIONAL: In addition to the 1000 records needed to be added to the database, if you are able to find a big list of doctors in the "GTA" with names and phone numbers, but lacking other information, please provide us a SEPARATE quote to offer us this list of doctor records for later use.
NOTE: this can lead to other follow-up opportunities later, please provide quality work.
Ask if have any questions.
PCB Design FTDI USB-USART Interface
penX JavaScript tag */-->
Additional files submitted: (Files are only available for logged in users)
FTDI+Interface.png
Additional files submitted: (Files are only available for logged in users)
FTDI+Interface.png
PCB Implementation Assistance for TopGunPK
25 components and is very simple. Mostly connecting DSub connectors and some opto-isolation. Images are attached. Project will be completed when I have circuit boards in hand.
People who apply must have electrical circuit design experience and experience with outsourcing PCB fabrication.
People who apply must have electrical circuit design experience and experience with outsourcing PCB fabrication.
PCB Implementation Assistance from TopGunPk
25 components and is very simple. Mostly connecting DSub connectors and some opto-isolation. Images are attached. Project will be completed when I have circuit boards in hand.
People who apply must have electrical circuit design experience and experience with outsourcing PCB fabrication.
People who apply must have electrical circuit design experience and experience with outsourcing PCB fabrication.
proteous PCB +academic writing
ld be done in 1 day ) 20% payment
2: Report writing for a digital testing research paper in 2 languages ( should be in MAX 14 days).
English (40% payment) and Hindi (full payment)
First project is 5 mins work
files will be sent to freelancers who show their previous work required for the project
budget 30-40$ for both .
2: Report writing for a digital testing research paper in 2 languages ( should be in MAX 14 days).
English (40% payment) and Hindi (full payment)
First project is 5 mins work
files will be sent to freelancers who show their previous work required for the project
budget 30-40$ for both .
ANALOG BOARD PCB layout under Altium Designer
Additional information submitted: 03/15/2011 at 11:16 EDT:
errata: is "8 asymetrical/differential inputs", should be "8 symetrical/differential inputs"
